|
GLT43300, GLT43301, GLT43302, GLT43303, GLT43304, GLT43308
1, 2, 3, 4 & 8-Channel, Gigalink 433MHz Handheld Transmitters
Features
• One, two, three, four & eight channels.
• More than four billion code combinations and no dipswitch visible, enabling it to be used for high security applications.
• 433 MHz transmissions. No interference from electrical noise and other signals.
• Microcontroller technology, replaces the traditional dipswitch coding which eliminates any possible code grabbing.
• Built-in battery monitor. Red LED indicates to the user when the battery is flat.
• Ability to program un-limited number of transmitters to a receiver, making expandability unlimited.
• Uses Gigalink technology, this involves using a receiver cable to program the transmitter. Some transmitters and receivers are programmed through the air. This is very risky since another person can grab your code.
Applications
• Security, wireless activation/deactivation of domestic or industrial alarms
• Gate operation
• Panic buttons
• Remote Activation of lights
• Simultaneous operation of multiple on/off functions |
 Click image to enlarge
 Download Datasheet
|
Description
The hand held 433MHz GIGALINK™ transmitters are an advanced Remote Control technology available in the world today. GIGALINK™ is an invention that has revolutionised the entire Remote Control technology including Elsema's earlier version of FMT- … and FMR- … series. The GLT43301/2/3/4/8 state-of-the-art invention brings a new dimension in the world of Remote Control technology in domestic, commercial and industrial applications.
Operating Distance
An operating distance (in conjunction with our GLR433.. series receivers) of 350 metres is possible.
The operating distance depends upon the receiver antenna and location. An independent test revealed the following ranges:
Range (Metres) |
Receiver Antenna |
Receiver Type |
50 |
345 mm Long Wire |
GLR433.… |
200 |
690 mm Long Wire |
GLR433.… |
350 |
ANT433S |
GLR433.… |
Range tests were done in an open area test site with line-of-sight operation and the receiver antenna wire was fixed vertically, away from any metal objects.
Case
The hand held GIGALINK™ transmitters are supplied with a case. There is also sufficient space on the rear of the case to place additional stickers such as your telephone contact, local authorities approval numbers etc.
Products in the Range
Click image to enlarge
|
Click image to enlarge
|
Click image to enlarge
|
Click image to enlarge
|
Click image to enlarge
|
GLT43300
Transmitter |
GLT43301
1-Channel |
GLT43302
2-Channel |
GLT43303
3-Channel |
GLT43304
4-Channel |
Click image to enlarge
|
Click image to enlarge
|
Click image to enlarge
|
Click image to enlarge
|
NL: No label
The Elsema Label is absent. |
GLT43308
8-Channel |
|
|
GLT43308NC
8-Channel, No Case |
Click image to enlarge
|
Click image to enlarge
|
Click image to enlarge
|
Click image to enlarge |
Click image to enlarge |
|
|
|
|
|
Technical Data
| Models |
GLT43301, GLT43302, GLT43303, GLT43304 |
GLT43308 |
| Power Source |
9V Battery (Applied to the battery Clip) |
9V Battery (Applied to the battery Clip) or
10-16VDC (Only applied to + & - terminals) |
| Current Consumption |
Max 45mA at 8VDC (Only when transmitting) |
Max 70mA at 12VDC (Only when transmitting) |
| Standby Current |
10uA (Typical) |
| Transmission Modes |
Continuous: Transmits as long as the channel is activated. Minimum transmission time is 640ms
Burst (B version): Transmits one 640ms burst for each channel activation, even if channel is activated for less than 640ms. |
| Battery Monitor |
LED flashes at 1Hz, during transmission, when battery voltage is at 6.5V (flat 9V battery) |
| Normal Operation |
The LED flickers at 12.5Hz during normal operation |
| Operating Freq |
433.920MHz (Other frequencies available on request. Refer to the table below )
|
| Carrier Freq Tolerance |
Crystal controlled 30 parts per million |
| Operating Temperature Range |
-5 to 50°C |
| Radiated RF Power Output |
100uW |
|
| Antenna |
Built-in loop Antenna |
| Type of Emission |
AM 100% depth |
| Freq Deviation Limiting |
1600 - 1900Hz non-return to zero |
| Modulation Freq |
120Hz to 1.8kHz (15% tolerance) |
| Spurious Transmission |
At least -60dB / carrier |
| Necessary Bandwidth |
±2.5kHz |
| Digital Coding System |
Microcontroller based 96-bit word |
| Code Combination |
Approximately 4.3 billion |
| Digital Channels |
1, 2, 3 or 4 channels. The type of membrane label determines the number of channels. Customers can fit custom-made membrane labels |
8 channels. On board 16-pin IC socket. Channels are addressed by joining opposite side of the IC socket pins. Elsema has a 16-pin 35cmm ribbon cable plug available |
| Dimension |
81 x 56 x 24mm |
130 x 67 x 27mm (GLT43308)
70 x 50 x 14mm (GLT43308NC) |
| Weight |
51g excluding battery |
60g (GLT43308)
35g (GLT43308NC) |
| Useable Receivers |
GLR433... series |
| Useable Operating Range |
Up to 350m, depending on receiver antenna and location |
Available Frequencies
SF2 |
433.664 MHz |
SF3 |
433.408 MHz |
SF4 |
433.152 MHz |
SF5 |
434.688 MHz |
SF6 |
434.432 MHz |
SF7 |
434.176 MHz |
SF8 |
433.792 MHz |
SF9 |
434.304 MHz |
Please quote Correct SF number when ordering transmitters on special frequencies.
Block Diagram
 GLT43301, GLT43302, GLT43303, GLT43304
 GLT43308(NC)
Connection Diagram GLT43300NC
Connection Diagram GLT43308NC
Customised labels
The transmitters are available without the front label. Customers can purchase the GLT43300, which is a hand held GIGALINK™ transmitter without the front label. This enables the customers to fit their custom made labels that can be a 1, 2, 3 or 4 channels. This has the advantage of customers only stocking one model to function as a 1, 2, 3 and 4 channel. Details of label dimensions are given on the following page. Customers will be provided with blank membranes, free of charge.
Elsema will provide (free of charge) blank membranes for customers who want to design their own labels.
Recommended label material is polyester autotex F200 and buttons to have tactile action with 10.7mm round pillow emboss.
Label Supplier :
Permark Industries Aust (1999) Pty Ltd
Telephone: (61) 2 9911 6656
Fax : (61) 2 9819 6517
Email : amrat@permark.com.au
|
