|
GLR08
Gigalink™ 8-Channel Decoder for R433 Receiver
Features
• Easy connection with R433 to form an 8-channel receiver
• Receiver with 8 solid state outputs
Applications
• security, industrial machine monitoring, crane control, level monitoring, multiple on/off functions |
 Click image to enlarge
 Download Datasheet
Programming Instructions
|
Description
The GLR08 can be connected with the R433 data receiver to form an 8-channel receiver. Connecting both units is simple. The GLR08 has a 3-way terminal block marked as + D - which should be connected directly to the R433 3-way terminal block marked as + D - . If the R433 is with a plastic case the connection is via a socket which is marked + D - . This connection is graphically shown at the bottom. The receiver can be used with the GLT08 / T433 transmitter to give an operating range of 1 Kilometres, line of sight, for each of the eight channels.
Each channel is addressed via the terminal block or the IC socket. The channel is activated when the corresponding channel number is shorted to ground. Each of the eight digital channel codes is stored in a microcontroller, which replaces the traditional dip switch.
The GLR08 and R433 can be purchased with Elsema's C160 weatherproof case and ANT433S UHF antenna.
Channels
The eight channels are solid state outputs using the ULN2803 Integrated Circuit. This IC is inserted to a socket that enables the user to easily change the output stage in case of a damaged output. The ULN2803 IC is available from Elsema. Output 1 being at the left and output eight to the right of the terminal block.
Different Modes for each Output
Modes are user selectable from the 3-way dip switch, shown below.
Case
The GLR08 can be supplied with or without a case. This allows the receiver to be integrated according to your needs.
Technical Data
| Supply Voltage |
10.0 to 28 V AC/DC. Absolute maximum DC 40 Volts.
Can use Elsema 12-volt AC power pack (12PP1000).
Supply lines should be less than 3 metres long to comply with radio frequency authorities. |
| Current Consumption |
5mA standby, 16mA if all outputs “On” |
| Operating Temperature Range |
-5 to 50°C |
| Decoding System |
Microcontroller based 96-bit word |
| Code Combinations |
4,294,967,296 |
| Outputs |
Eight Open Collectors (See chart for Collector Currents)
Chart indicates that eight outputs can be ON simultaneously with each output collector current being 125mA. Outputs can hold 50 Volts in “Off” state |
| Output Modes |
User selectable from DIP switch
1 |
2 |
3 |
Mode |
Description |
Off |
Off |
Off |
All Momentary |
Outputs on, only while correct signal is received. |
On |
Off |
Off |
All Flip- Flop |
Outputs alternate at every correct incoming signal. |
Off |
On |
Off |
Momentary and Flip-Flop |
Outputs 1 to 4 are momentary and 5 to 8 are flip-flop. |
On |
On |
Off |
Latching on |
Outputs will be on until supply to receiver is momentarily interrupted. |
Off |
Off |
On |
Momentary and Flip-Flop |
Outputs 1 to 6 are momentary and 7 to 8 are flip-flop |
On |
Off |
On |
Momentary and Flip-Flop |
Outputs 1 to 2 are momentary and 3 to 8 are flip-flop |
Off |
On |
On |
Momentary and Flip-Flop |
Outputs 1 to 3 are momentary and 4 to 8 are flip-flop |
On |
On |
On |
Latching and Momentary |
Output 1 is latching and 2 to 8 momentary |
|
| Connections |
Supply: 3-way screw type terminal block
Eight Outputs: 9 -way screw type terminal block. (8 open collectors plus Ground). |
| Dimensions |
96 x 70 x 15mm |
| Weight |
55g |
| Useable Transmitters |
All Elsema Type 433MHz GLT-... series |
Block Diagram
|
