|
FMTR-2713
27MHz 1 Watt Repeater
Features
• Ideal to increase range to 3000m
• Weather proof case also available
Application
• Transmission range extension
Care should be taken not to transmit without an antenna |
|
 Click image to enlarge
 Download Datasheet
|
Description
The FMTR-2713 is a 27MHz repeater. With its highly sensitive receiver and a 1 Watt transmitter, it is ideal to increase the range of a transmitted signal to 3000 metres. This transmitted signal can be any of Elsema's FMT-… series transmitters. For example the KEY-301 transmitter has a maximum transmitted range of 80 metres, however when used with the FMTR-2713 repeater the effective range is increased up to 3000 metres.
A suitable 27MHz antenna should be connected to the SO239 socket. We recommend the Elsema ANT27L antenna.
The FMTR-2713 can be ordered with a weather proof plastic case or as a Printed Circuit Board (See picture) assembly. This PCB assembly enables customers to integrate the repeater into their own product or case.
The FMTR-2713 repeater comes in three different models i.e. 9510V…, 9511V… and 9512V… . The three models are determined by inserting the correct micro-processor on the repeater board.
Each repeater is factory set and the micro-controller is labeled with the correct model number. All micro-controllers are inserted into a 28-pin IC socket. This socket gives the added advantage of changing the repeater to a different model. Customers must specify which model they require when ordering the repeater.
Compatibility
All Elsema type FMT-… series
KEY-301, KEY-302, KEY-304
FMT-301, FMT-302, FMT304
FMT-401, FMT-404
FMT-312
FMT-2712
Technical Data
Supply |
11-13.6 Volts DC (for constant RF-Output), screw type terminal block. Do not use AC supply. |
Current Consumption |
Transmitting 370mA
Receiving 16mA (standby). |
Operating Frequency |
27.145MHz (Other frequencies available: 27.045, 27.195 & 27.455MHz. NB. 27.455MHz is available for Europe Only). |
Carrier Freq Tolerance |
Crystal controlled, 30 parts per million (0-50 deg C). |
RF Power Output |
1W into 50 Ohms at 13.6VDC, SO239 Socket. |
Antenna |
SO239 socket is provided. Optimum performance use Elsema ANT27L antenna. |
Type of Emission |
Narrow-band-width Frequency Modulation (5K00F1D). |
Transmitter |
FMT-2712 |
Receiver |
FMR-05 |
Mounting Hole Size |
3.17mm or 1/8" |
Mounting Hole Spacing |
Length 120mm 4.72"
Width 60mm 2.36" |
Weight |
106g (without weather proof case). |
Useable Operating Range |
Up to 3000m, depending on installation and type of antenna used. Recommended Antenna is Elsema's ANT27L. |
Instructions
FMTR-2713A is using the 9510V… Micro-Controller. The repeater is checking the first 8 bits of the received word and if it is matching its own 8-way code switch, will re-transmit these 8 bits together with the last 4 bits it received. This model can be used when a group of transmitters should be repeated (Not all transmitters). If a multi channel receiver (Such as FMR204-12) is used to receive the repeated transmission, each transmitter, which transmits into the repeater, can be identified.
The 2-way mode switch (Between the supply terminal block and the 12-way code switch) has no function and is reserved for the future use. |
FMTR-2713B is using the 9511V… Micro-Controller. This model uses the 2-way mode switch (Between the supply terminal block and the 12-way code switch), allowing four different modes of repeating.
2-way Mode Switch Configuration of FMTR-2713B is as follows:
Switch 1 - Repeat Modes |
| ON |
It is comparing all 12 bits of the received word with the 12-way code switch and if matching, will re-transmit this unique code . |
| OFF |
It is comparing the first 8 bits with code switches 1 to 8, and if matching, will re-transmit this 8 bits, together with the current data on code switch inputs 9 to 12. |
Switch 2 - Response Time |
| ON |
Repeater will transmit as soon as correct received word is matching the 8-way or 12-way code. |
| OFF |
Repeater will transmit after reception of correct code has ended . |
|
FMTR-2713C is using the 9512V… Micro-Controller. Repeater will repeat any received 12 bit code switch data. This model also uses the 2-way mode switch (Between the supply terminal block and the 12-way code switch), allowing four different modes of repeating.
This type of repeater will respond to any of Elsema's FMT-… series transmitters. It should not be used in an area or location where other transmitters for garage doors, alarms, etc. are expected since the repeater would splatter the 27MHz frequency.
2-way Mode Switch Configuration of FMTR-2713C is as follows:
Switch 1 - Repeat Modes |
| ON |
The repeated data is re-transmitted as opposite
data. Therefore an “on” received, by the repeater, is
repeated as an “off” and receiver is disabled for 4 seconds. |
| OFF |
The repeated data is re-transmitted as normal
data and receiver is disabled for 4 seconds. |
Switch 2 - Response Time |
| ON |
Repeater will transmit as soon as a valid ELSEMA code is received. |
| OFF |
Repeater will transmit after reception of the ELSEMA code has ended . |
|
Special Versions
9512V609A: Same as 9512V, except data is opposite and receiver is disabled for 4 seconds.
9512BV05: Same as 9512V, except data is not opposite and receiver is disabled for 4 seconds.
Please Note:
• After a valid reception, all 3 models are repeating the transmission for 0.5 seconds only (Optional times are available), after which they go back into receive mode to check for another valid reception.
• The 12-way code switch is inserted into a socket. This enables the user to replace the 12-way code switch with a 8-way code switch and use 9 to 12 for data. An 8-way code switch is available from Elsema.
• The repeater has an on board red LED which indicates that a code is repeated (transmitting).
|
