|
FMR15101240
1 Channel 151MHz, Receiver with mains AC supply
Features
- Supply voltage 240VAC (also available in 110-120VAC supply for international markets)
- High efficiency toroidal transformer
- High capacity output relay
- Test push buttons for the relay
- Momentary, Flip Flop, Latching and Off delay modes are all user selectable.
- Optional QM150 bracket available for easy mounting to cases or walls.
- Also available in an IP66 rated case for outdoor installations
Application
- Pump Control
- Long distance panic button
- On/Off applications in agricultural devices
- Basic Telemetry eg. Water level indication
- Security alarm
 Click image to enlarge
|
Click image to enlarge |
FMR15101240Q
1- Channel 240VAC Supply in Quick Mount |
FMR15101240E
1- Channel 240VAC Supply in an IP66 rated Case |
|
Click image to enlarge
 Download Datasheet
|
Description
The 151MHz receivers use dual conversion, narrow band FM which makes it ideal for industrial applications. Built into the receiver is a noise and signal strength indicator. The user selectable frequency synthesizer allows for easy installation on a frequency that is not in use, allowing optimal performance in the receiving range.
The toroidal transformer on this receiver is 25-30% more efficient than the conventional types. It has a low operating temperature, low hum and low stray magnetic field.
Connecting wires to the receiver has been made easier by the pluggable type terminal block. An on board LED indicates when power is connected and an extra LED on the board to indicate when the relay is activated. There is a test button for the relay output to test your connections.
The receiver’s high capacity output relay is capable of switching up to 16 Amps of resistive load and up to 8 Amps of inductive load. A world first for a standalone receiver.
The receiver can be mounted to a Quick Mount or in a weatherproof case with an IP66 rating.
Different Modes for the Output
This 3-Way dip switch is situated beside the microcontroller. (refer to the picture below)
Modes are user selectable from the 3-way dip switch, shown below.
Coding
The 12 way dip switch on the receiver sets the 12 bit unique code for the system. This has to be matched to that on the transmitter.
Apart from the 12 way dip switch there will be an additional dip switch depending upon the receiver type:
- Single channel receiver will have a 3 way dip switch.
This DIP switch on the right side of the 12 way dip switch denotes the channel. See table below.
Generally to use a 1 channel Tx to 1 channel Rx match all the 15 dip switch (12way + 3way just on the right side of the 12 way).
To use a multi channel Tx to control a number of (up to 8) Rx, refer to the table below for the switch setting.
FMR15101
3-Way DIP Switch & Single Relay Output
SW13 |
SW14 |
SW15 |
Channel |
OFF |
OFF |
OFF |
1 |
OFF |
OFF |
ON |
2 |
OFF |
ON |
OFF |
3 |
OFF |
ON |
ON |
4 |
ON |
OFF |
OFF |
5 |
ON |
OFF |
ON |
6 |
ON |
ON |
OFF |
7 |
ON |
ON |
ON |
8 |
Signal Strength Indicator
The 151MHz receivers have five blue LED’s on the board. The table below indicates the level of the valid transmitted signal.
5 LED’s on |
-70dBm |
Very Strong signal |
Very Reliable operating conditions |
4 LED’s on |
-75dBm |
Very Strong signal |
Very Reliable operating conditions |
3 LED’s on |
-80dBm |
Very Strong signal |
Very Reliable operating conditions |
2 LED’s on |
-90dBm |
Strong signal |
Very Reliable operating conditions |
1 LED on |
-100dBm |
Good signal |
Reliable operating conditions |
Noise Strength Indicator
If more than 1 led is “ON” without a valid transmission, this indicates that there is noise on the frequency selected. Change the 3-way dipswitch on the receiver module to select a different frequency.The default setting is for 151.6MHz (All 3 dipswitches “ON”). Below is a table with the Dipswitch settings and the frequencies.
Frequency |
1 |
2 |
3 |
151.600 MHz |
On |
On |
On |
152.375 MHz |
Off |
On |
On |
151.775 MHz |
On |
Off |
On |
151.400 MHz |
Off |
Off |
On |
151.175MHz |
On |
On |
Off |
151.025 MHz |
Off |
On |
Off |
150.900 MHz |
On |
Off |
Off |
150.825 MHz |
Off |
Off |
Off |
Products in the Range
Technical Data
Supply Voltage |
240Volts AC Mains
(110-120VAC available on request)
Supply lines should be less than 3 metres long to comply with radio frequency authorities. |
Current Consumption |
18mA |
Receiver Type |
Dual Conversion Superheterodyne |
Receiving Frequency |
151.6MHz (8 selectable frequencies. See table above) |
Oscillation System |
VCO with 10ppm crystal controlled reference oscillator |
Operating Temperature Range |
-5 to 50°C |
IF Frequency |
10.7MHz |
Sensitivity |
Better than 0.5uV (For relay to activate) |
Selectivity |
Better than -6dB at ±25kHz |
Type of Demodulation |
Narrow-Bandwidth Frequency Modulation (FM) |
Occupied Bandwidth |
25kHz at -20dB |
Connection |
Supply, Antenna & Outputs - pluggable type terminal blocks |
Output |
Change over relay output, rated at 16 Amps of resistive load and up to 8 Amps of inductive load. |
Antenna |
50Ω, 151MHz Antenna, Elsema ANT151M for maximum performance
A piece of approximately 1metre wire can be used for short range applications |
Dimensions |
130 x 70 x 37mm |
Mounting Hole Size |
3.97mm or 5/32” |
Weight |
168g |
Useable Transmitters |
All FMT151 series (with correct setting on the three way dip switch) refer to the table above. |
Useable operating range |
Up to 5000 metres, depending on installation and type of antenna used. Recommended Antenna is Elsema ANT151M |
Block Diagram
Application Diagram
FMR15101240
|
