FMR-24002
2 - Channel, 240V AC Receiver with 240V AC/DC 8A Relay Output

Features

• Highly sensitive receiver input stage.
• Crystal controlled for high stability and performance.
• Uses micro-controller technology that can be re-programmed to suit unique applications.
• Momentary, flip-flop and latching output modes is user-selectable.

Applications

• Pump Control
• Long distance panic button
• On/Off applications in agricultural devices
• Security alarm
• Basic Telemetry eg. Water level indication.


 Click image to enlarge
Download Datasheet

Description
Technical Data
Products in the Range
Block Diagram
Application Diagram

 

Description

The FMR-24002 is a crystal controlled two channel receiver, comprising of receiving, decoding and relay-output sections. A specially designed micro-controller is used in the decoder section, which ensures operation for highest reliability.

The receiver works on a digitally encoded 27 MHz frequency modulated (FM) signal. It may be used in applications such as the remote control of garage doors, gates, lights, alarms or in any other new or existing installations where the use of conventional wiring is difficult or impossible to accomplish.

If the code of the input signal (from a transmitter) matches the setting of the coding switch on the receiver (up to 4096 combinations), an output is obtained i.e. the relay operates. This relay provides a clean set of contacts for switching AC/DC current up to 8 Amps.

Connection to the receiver is via a eight-way screw-type terminal block. The receiver can be mounted to a Quick Mount or in a C160 weatherproof case.

A proper 27 MHz CB-Antenna will give a reliable control range of up to 200 metres, when used with Elsema’s FMT-301, FMT-302, FMT-304 transmitters. If a CB-Antenna is used, the shield of the cable must be connected to the "Sh terminal".

Different Modes for the Output
Modes are user selectable from the 2-way dipswitch. Dipswitch 1 corresponds to relay channel 1 and dipswitch 2 corresponds to relay channel 2.

Momentary Mode If the dipswitch is “off” the relay will be in momentary mode.
Flipflop Mode If the dipswitch is “on” the relay will be in flipflop mode.
Latching If latching is required (Relay stays on until power is removed) the latching link should be inserted and soldered into the two holes to the right of the 2-way dipswitch. This will enable corresponding relays to latch.

Care must be taken, not to bring a receiver near strong magnetic fields, such as DC-Motors, speakers, magnets for reed switches, transformers etc. as it would magnetise the coils and may cause severe de-tuning.

Technical Data
Supply Voltage

240 Volts AC mains.
110, 115 or 120 VAC available on request only.
Supply lines should be less than 3 metres long to comply with radio frequency authorities.

Current Consumption

18mA, on 240V AC

Receiver Type Dual Conversion Superheterodyne
Receiving Freq 27.145MHz (Other freq available on 27.045, 27.195, & 27.455MHz. The 27.455 freq is not available for Australia)
Type of Crystal Used 10.245MHz, Fundamental, 20pf, 30ppm
16.495MHz, Fundamental, 20pf, 30ppm
Operating Temperature Range -5 to 50°C
IF Freq 455kHz
Selectivity At least -40dB at ±10kHz
Image Rejection At 26.285MHz better than -60dB
Sensitivity 1uV (for output to activate)
Type of Demodulation Narrow-bandwidth Frequency Modulation (FM)
Occupied Bandwidth ±2.5kHz
Decoding System Microcontroller based 96-bit word
Code Combinations 1024
Output Change over relay output, rated at 8 Amps/240 Volts
Connections

8-way screw type terminal block for Supply and Relay
2-way screw type terminal block for Antenna

Antenna 50 ohms, 27MHz CB-Antenna or approximately 300mm long wire for short range applications.
Dimensions 130 x 70 x 37mm
Mounting Hole Size 3.97mm or 5/32"
Weight 140g
Useable Transmitters All Elsema Type 27MHz FMT-... series

Products in the Range

 Click image to enlarge

 Click image to enlarge 

 


 Click image to enlarge

FMR-24002
2- Channel 240VAC Supply

FMR-24002Q
2- Channel 240VAC Supply in Quick Mount

FMR-24002E
2- Channel 240VAC Supply in C160 Weatherproof Case

Block Diagram

Application Diagram

 

FMR-24002

 


© 2008 Elsema Pty Ltd. All rights reserved.