Elsema Pty Ltd - FMR-212T

FMR-212T
10-28VAC/DC Receiver with Timer Controlled Relay Output

Features

• Crystal Controlled
• Digitally Encoded
• Delayed-off Output

Click image to enlarge

FMR-212T - Receiver with Timer Controlled Relay Output

Click image to enlarge

FMR-212TE - FMR-212T with UBB plastic case

Click image to enlarge
Download Datasheet

Description

Products in the Range

Technical Data

Application Diagram

Receiver Selection Table

Description

The FMR-212T is a 10-28V single channel receiver with 9 different relay output modes. Each mode is user selectable by changing the setting on the 4-way DIP switch. Modes include momentary, flip-flop, 1-10 second delayed off, 10-300 second delayed off, pulsing, latching, on-off, custom and test.

9 Different Relay Output Modes of FMR-212T
A 4-way dip switch allows the user to select between 9 different output modes. This is shown below:

4-Way Dip Switch Mode Settings The output relay will respond in the following manner when receiving the correct signal from a transmitter
	Momentary Relay on, only while correct signal is received.
	Flip- Flop Relay alternates at every correct incoming signal.
	Delayed Off 1 Relay on, but delayed off for 1-10 seconds, adjustable by trimpot.
	Delayed Off 2 Relay on, but delayed off for 10-300 seconds, adjustable by trimpot.
	Pulsing Relay will pulse at 1 Hz for 10 - 300 seconds, adjustable by trimpot.
	Latching on Relay will energize until supply to receiver is momentarily interrupted.
	On-Off This mode requires a 2-channel Tx. Channel 1 will always energize the relay. Channel 2 will always de-energize the relay.
	Custom This mode is reserved for specific customers' requirements.
	Test Relay is energized, for test purpose only.

Compatibility

All Elsema type FMT-… series
KEY-301, KEY-302, KEY-304
FMT-301, FMT-302, FMT-304
FMT-401, FMT-402, FMT-404
FMT-312E, FMT-31202E, FMT-31204E

Products in the Range


FMR-201 Single Channel Receiver with Open CollectorOutput	FMR-203 2-Channel PCB Strip Receiver	FMR-212 Single Channel Receiver with Relay Output	FMR-212T Single Channel Receiver with Timer Controlled Relay Output	FMR-240 Single Channel 240V Receiver with Relay Output

FMR-24002 2-Channel 240VAC Receiver with 2 Relay Outputs	FMR-202 2-Channel Receiver with 2 Relay Outputs	FMR204-12 4-Channel 12V Receiver with 4 Relay Outputs	FMR204-24 4-Channel 24V Receiver with 4 Relay Outputs	FMR-204/16 4/16 Channel Receiver with Open Collector Outputs

FMR-232R Computer Receiver with 2 Relay Outputs & Database Software	FMR-100 Receiver for Multi-Channel System	RXD-101 Decoder for Multi-Channel System

Technical Data

Supply Voltage	11.0 - 28 Volts DC, 10.0 - 28 Volts AC Can use Elsema AC power supply 12PP1000 or 24PP
Current Consumption	15mA stand by at 12 Volts DC; 44mA if relay is "ON" at 12 Volts DC
Receiving Frequency	27.145MHz (Other frequencies available: 27.045, 27.195 & 27.455MHz. NB. 27.455MHz is available for Europe Only)
Type of Crystal Used	26.690MHz, 3rd overtone, 20pF, 30ppm at 0-50°C
IF Freq	455kHz
Selectivity	At least -40dB at ±10kHz
Sensitivity	Better than 1uV (for relay to switch on)
Type of demodulation	Narrow-bandwidth Frequency Modulation (FM)
Band Width	±2.5kHz
Decoding System	Onboard 12-way coding switch (4096 digital channels)
Output	Change over relay output, rated at 5A / 240V
Relay Contacts	Common (C) Normally Close (NC) & Normally Open (NO)
Connections	6-way screw type terminal block
Timer	Adjustable from 1-300 sec. Refer to table for selecting different output modes.
Antenna	Elsema’s ANT27MHz series antennas or piece of approximately 300 mm long wire for short range applications.
Dimensions	96 x 70 x 20mm
Mounting	Clip into a QM100 Quick Mount or UBB plastic case
Weight	67g
Compatible Transmitters	All Elsema type FMT-... 27MHz series and KEY-3.. series

FMR-212T, 12/24 V Application

12/24V Application

FMR-212T, 240/110 VAC Application

240Vac Application