FMR204-12 & FMR204-24
27MHz Receiver with 4 Channels, 12 or 24 Volt Supply

Features • Crystal Controlled • 4-Channel • Digitally Encoded Applications • Remote control of garage doors, gates, lights, alarms  Click image to enlarge  Click image to enlarge FMR2704-12 4-channel, 12V Relay Output FMR2704-24 4-channel, 24V Relay Output

Click image to enlargeDownload Datasheet Description Products in the Range Technical Data Block Diagram Receiver Selection Table

Description

The FMR204-12 and FMR204-24 are crystal controlled four-channel receivers, comprising of receiving, decoding and relay-output sections. A specially designed MICRO-PROCESSOR is employed in the decoder section, which ensures operation at low supply voltage, highest reliability, associated with very low power drain.

The receiver works on a digitally encoded 27 MHz frequency modulated (FM) signal. It may be used in applications such as the remote control of garage doors, gates, lights, alarms or in any other new or existing installations where the use of conventional wiring is difficult or impossible to accomplish.

If the code of the input signal (from a transmitter) matches the setting of the 10-way code switch on the receiver (up to 1024 combinations), an output is obtained i.e. the relay operates. This relay provides a clean set of contacts for switching DC current up to 5 Amps. Code switches eleven and twelve are addressed by the four channels. The four channels are binary encoded on eleven and twelve.

The supply and antenna connections to the receiver are via a four-way screw-type terminal block, with a separate twelve-way terminal block for the relay connections.

The receiver can be clipped to a Quick Mount enabling the receiver to be easily mounted against walls, roof etc.

Elsema’s ANT27MHz series antennas will give a reliable control range of up to 200 metres, when used with Elsema’s FMT-301, FMT-302 and FMT-304 transmitters.

The four-way code switch allows individual control of each relays output mode. In the momentary mode (MOM) the output relays are only activated while the correct signal is received. In the flip/flop mode ("FF") the output relays are toggled with every correct incoming signal. This enables the direct use for switching on/off lights etc. In flip/flop mode, the relays are off at the initial "power-up".

Care must be taken, not to bring a receiver near strong magnetic fields, such as DC-Motors, speakers, magnets for reed switches, transformers etc. as it would magnetise the coils and may cause severe de tuning.

Compatibility

All Elsema type FMT-… series
KEY-301, KEY-302, KEY-304
FMT-301, FMT-302, FMT-304
FMT-401, FMT-402, FMT-404
FMT-312E, FMT-31202E, FMT-31204E

Products in the Range

FMR-201 Single Channel Receiver with Open CollectorOutput	FMR-203 2-Channel PCB Strip Receiver	FMR-212 Single Channel Receiver with Relay Output	FMR-212T Single Channel Receiver with Timer Controlled Relay Output	FMR-240 Single Channel 240V Receiver with Relay Output
FMR-24002 2-Channel 240VAC Receiver with 2 Relay Outputs	FMR-202 2-Channel Receiver with 2 Relay Outputs	FMR204-12 4-Channel 12V Receiver with 4 Relay Outputs	FMR204-24 4-Channel 24V Receiver with 4 Relay Outputs	FMR-204/16 4/16 Channel Receiver with Open Collector Outputs
FMR-232R Computer Receiver with 2 Relay Outputs & Database Software	FMR-100 Receiver for Multi-Channel System	RXD-101 Decoder for Multi-Channel System

Accessories

Click image to enlarge	Click image to enlarge
Quick Mount QM100	Plastic Case C160

Technical Data

Block Diagram

FMR204-12 & FMR204-24 12/24 VDC Application

FMR204-12 & FMR204-24 240/110 VDC Application